Core Semiconductor Processes: Step 10

CMP & Wafer
Grinding

At Nanosystems JP Inc., we offer chemical mechanical polishing for metals, insulators, and polymers, up to 12-inch wafers. Custom slurries for Cu damascene, Si, and SiC. Pre-bonding CMP for fusion and hybrid bonding. Optical grade polishing. Wafer thinning to 50 µm for TSV reveal and 3D packaging. Compound semiconductor grinding: SiC, GaN, InP, GaAs, LiTaO₃.

Have full specs ready? Submit a detailed Technical RFQ →

CMP metals · insulators · polymerCustom Cu/Si/SiC slurriesPre-bonding CMPOptical grade polishingWafer thinning to 50 µmTSV backside grindingSiC · GaN · InP · GaAsLiTaO₃ · Sapphire
50 µm
Min wafer thickness after grinding
12 inch
Max wafer size for CMP
Custom
Slurry formulations
SiC/InP/GaAs
Compound semi grinding
CMP, Chemical Mechanical Polishing
Planarization for metals, insulators, and polymers

CMP combines chemical etching and mechanical abrasion to create near-atomically smooth surfaces, essential for multi-layer device fabrication where surface topography must be controlled to within nanometers.

Metal CMP

Copper damascene CMP removes overburden Cu and stops precisely on the barrier layer, the key step in BEOL interconnect and RDL fabrication. Also: Al, W, Ta, and TiN planarization for MEMS electrodes, contact metals, and gate electrodes. Endpoint detection by eddy current (on Cu) or optical reflectometry prevents over-polish into the barrier layer. Cu dishing within wide lines and SiO₂ erosion between closely spaced lines are measured and reported post-CMP.

Cu damasceneAl · W · Ta · TiNEddy current endpointCu dishing measuredBEOL · RDL

Insulator CMP (SiO₂/SiN)

Oxide and nitride planarization for shallow trench isolation (STI) fill, pre-bonding surface preparation, and interlayer dielectric (ILD) planarization between metal layers. Excellent within-wafer uniformity across 12-inch substrates. Low defectivity slurry chemistries minimize scratch density on STI oxide, critical for maintaining gate oxide integrity adjacent to STI edges.

SiO₂ · SiNSTI fill planarizationILD planarizationPre-bonding surface prep12 inch wafer

Polymer CMP (Polyimide/BCB)

CMP of polyimide, BCB, and other organic dielectric layers used in RDL fabrication and advanced packaging. Planarizes polymer passivation layers after cure and patterning to enable subsequent Cu metallization and lithography. BCB CMP is particularly critical for FOWLP where multi-layer polymer RDL requires each layer to be perfectly flat before the next layer is coated.

Polyimide · BCBRDL planarizationFOWLPPolymer passivationAdvanced packaging

Pre-Bonding CMP

Ultra-precise CMP immediately before wafer bonding, achieving <0.5 nm Ra surface roughness required for direct fusion bonding (Si-Si) and Cu-Cu hybrid bonding. Local surface roughness is verified by AFM, and wafer-scale flatness is measured separately (interferometry or thickness mapping) to the agreed acceptance before the wafer pair proceeds to bonding. Even a single surface particle or scratch can create a void in the bond interface that propagates during annealing, pre-bonding CMP is the most defect-sensitive CMP application we perform.

<0.5 nm Ra targetAFM verifiedFusion bonding prepHybrid bonding prepZero tolerance for particles

Optical Grade Polishing

Angstrom-scale surface polishing for fused silica, quartz, sapphire, and calcium fluoride optical substrates. Required for high-power laser optics, UV photomask substrates, and precision mirror blanks where any surface micro-roughness increases scatter loss and reduces laser damage threshold. Polishing slurry, pad conditioning, and process parameters are different from semiconductor CMP, this is precision optics grinding, not standard semiconductor polishing.

Ra ≤0.1 nm optical gradeFused silica · QuartzSapphire · CaF₂High-power laser opticsUV photomask substrates

Custom Slurry Formulations

Custom CMP slurry formulations are available for non-standard applications: SiC polishing slurry for power device wafer preparation (SiC is among the hardest semiconductor materials, standard Si slurries do not work), Si wafer mirror polishing slurry, and custom oxide slurries for specific ILD materials. Custom slurry development typically requires 2-4 weeks of process qualification on monitor wafers before production use.

SiC custom slurrySi mirror polish slurryCustom ILD slurry2-4 week qualificationSiC power devices
Wafer Grinding & Thinning
From 4-inch to 12-inch, down to 50 µm

Wafer thinning by backside grinding is essential for TSV reveal, 3D packaging, and reducing thermal resistance in power devices.

Standard Si Wafer Thinning

Backside grinding of silicon wafers from 4 inches to 12 inches using infeed grinding for stable, controlled thickness. Target thickness down to 50 µm for TSV Cu tip exposure and 3D-IC stacking; prototype runs to 20 µm on request. Coarse diamond grinding removes bulk material; fine-mesh wheel finishing then reduces the sub-surface damage layer, improving die flexural strength without requiring a full CMP stress-relief step. A subsequent dry-polish or CMP step is also available where flatness requirements demand it. Within-wafer TTV target ±2 µm after polish; the mean final-thickness tolerance is set per route (see wafer thinning). Thickness map provided post-grind. Carrier wafer bonding available for wafers thinned below 150 µm. Singulated chip thinning also available on request.

4 to 12 inchDown to 50 µmTTV ±2 µm targetFine-mesh wheel finishStress relief after grindCarrier wafer supportSingulated chip thinning

Protective Tape Lamination & Removal

Backgrinding requires a protective tape on the device face to prevent surface damage during grinding. At Nanosystems JP Inc., we offer protective tape lamination before grinding and clean removal after, including UV-release tape for device-side adhesive that cannot withstand solvent exposure. Tape selection is matched to the wafer material, device topology, and subsequent process steps. This is included as part of the coordinated backgrinding service, not a separate job for the customer to manage.

Protective tape lamination UV-release tape available Post-grind tape removal Matched to wafer material 5 to 12 inch wafers

Backside Grinding for TSV Reveal

Controlled thinning specifically targeting TSV Cu tip depth, grinding to within a few micrometers of the Cu tips from the backside. Combined with subsequent dry etch reveal, PECVD passivation, and CMP to complete the TSV reveal flow. The grind target is set from the TSV depth, leaving a silicon margin above the insulated via tips; the tip protrusion is produced by the subsequent recess etch. Coordinated directly with our TSV reveal service, both steps handled in one project.

TSV reveal prepGrind stop above the insulated via tipsCoordinated with reveal etchSame PM as TSV reveal3D-IC · Interposer

Compound Semiconductor Grinding

Precision grinding of InP, GaAs, GaN-on-Si, and GaN-on-SiC wafers. Compound semiconductors have different mechanical properties than silicon, they are more brittle, have lower fracture toughness, and have preferential cleavage planes that cause chipping under standard Si grinding conditions. Dedicated grinding wheels and process parameters prevent edge chipping and surface cracking in these materials.

InP · GaAsGaN-on-Si · GaN-on-SiCDedicated grinding wheelsBrittle material handlingCleavage plane awareness

SiC Wafer Grinding

Silicon carbide is the hardest commonly processed semiconductor (Mohs hardness 9.5), requiring diamond grinding wheels and specialized process control. Post-grinding CMP with custom SiC slurry achieves the smooth low-RMS surface required for gate oxide growth on SiC MOSFETs. The combination of grinding + SiC CMP reduces the surface step-bunching and polishing scratches that degrade SiC gate oxide reliability.

4H-SiCDiamond grinding wheelsCustom SiC CMP slurryLow-RMS for gate oxideSiC MOSFET prep

LiTaO₃ / LiNbO₃ Grinding

Lithium tantalate (LiTaO₃) and lithium niobate (LiNbO₃) grinding and polishing for SAW (Surface Acoustic Wave) filter substrates. Both materials are piezoelectric single crystals requiring careful process control to avoid cracking along cleavage planes during grinding. Polished to the crystal-face roughness specification required for SAW device performance (Ra <0.5 nm for SAW frequency >2 GHz).

LiTaO₃ · LiNbO₃SAW filter substratesRa <0.5 nmCleavage plane control5G SAW filter substrates

Sapphire & Glass Grinding

Sapphire (Al₂O₃) grinding for LED substrate thinning, UV window thinning, and silicon-on-sapphire (SOS) substrate preparation. Glass substrate thinning and edge chamfering for large-format panel processing. Inspection by wafer surface analyzer (WSA) measures surface roughness, bow, and warp after grinding, results included in the lot process data sheet.

Sapphire · GlassLED substrate thinningSOS preparationWSA inspection includedLarge-format glass panels
Cu CMP Flow

How copper CMP is done,
step by step

From electroplated overburden to inlaid, planar copper: the sequence behind our damascene RDL and via fill work, ending at the same sub-0.5 nm Ra finish specified on this page.

1 · Plated Cu · overburden2 · Bulk Cu removal3 · Endpoint clearing4 · Barrier polish · stop5 · Clean + metrology · <0.5 nm RaDishing / erosion checked lot by lot
Copper CMP: from plated overburden to inlaid planar copper
Process Specifications
CMP and grinding parameters
ProcessEndpoint/MetrologyKey SpecificationApplication
Metal CMP (Cu)Eddy current endpointCu dishing ≤20 nm (100 µm line)Cu RDL, BEOL damascene, TSV CMP
Insulator CMP (SiO₂)Optical endpointWithin-wafer non-uniformity ≤5%STI, ILD, pre-bonding
Polymer CMP (PI/BCB)Time/thickness controlPlanarized to ≤5 nm stepRDL passivation, FOWLP
Pre-bonding CMPAFM surface measurementRa ≤0.5 nmFusion bonding, hybrid bonding
Optical grade polishingInterferometryRoughness ≤0.1 nm RMS (1 Å) on selected substratesLaser optics, UV substrates
Si wafer thinningThickness gaugeTTV ±2 µm target (mean tolerance per route); down to 50 µmTSV reveal, 3D-IC
SiC grinding + CMPWSA surface analyzerRa ≤0.3 nm post-CMPSiC MOSFET gate oxide prep
Compound semi grindingThickness gauge + WSAChipping and cleavage controlled by recipe; inspected per lotInP, GaAs, GaN, LiTaO₃
Applications
CMP and grinding across power, packaging, and photonics

3D-IC TSV Reveal

Backgrinding to 50 µm approaches Cu TSV tips from the backside; CMP after reveal etch exposes clean Cu contacts. Our CMP and grinding are coordinated with TSV fabrication and reveal in the same project.

Backgrind 50 µm → dry etch reveal → passivation CMP · TSV · 3D-IC

SiC Power Devices

SiC wafer grinding + custom SiC CMP slurry to achieve the low-RMS surface required for gate oxide growth. Carbon cap annealing combined with post-anneal CMP provides the lowest possible surface roughness on 4H-SiC for high-reliability MOSFET gate oxide.

Diamond grind → SiC custom CMP → gate oxide prep · SiC MOSFET · SBD

Wafer Bonding Preparation

Pre-bonding CMP achieves <0.5 nm Ra for fusion and hybrid bonding. Local roughness verified by AFM before bonding; flatness measured separately. The most common yield loss in wafer bonding is surface particle and roughness defects, our pre-bonding CMP targets both, with AFM verification before bonding.

CMP <0.5 nm Ra → AFM verify → bonding · Fusion · Hybrid bonding · 3D-IC

SAW Filter Substrates

LiTaO₃ and LiNbO₃ grinding and polishing for 5G SAW and BAW filter production. Surface roughness Ra <0.5 nm required for SAW frequency stability above 2 GHz. Cleavage-plane-aware grinding prevents yield loss from crystal cracking.

LiTaO₃ · LiNbO₃ · Ra <0.5 nm · SAW filters · 5G · RF front-end

Silicon Photonics

Pre-bonding CMP for SOI wafer bonding, achieving the flatness needed for direct bonding of silicon photonic device layer to handle wafer. Optical grade polishing for fused silica waveguide substrate preparation.

Pre-bonding CMP · SOI bonding · Fused silica polishing · SiPho substrate

LED & Sapphire Substrates

Sapphire substrate thinning for LED chip-scale packaging and silicon-on-sapphire (SOS) sensor substrates. Post-epitaxy sapphire back-thinning for laser lift-off and GaN LED singulation by stealth laser dicing.

Sapphire thinning · LED CSP · Laser lift-off prep · GaN LED · SOS
Why Nanosystems JP Inc.
CMP and grinding integrated with packaging and bonding
01

Custom SiC slurry expertise

SiC requires a specifically formulated abrasive slurry, not the same chemistry as silicon CMP. SiC polishing slurries specifically for power device substrate preparation are available.

02

Integrated TSV reveal flow

CMP, backgrinding, dry etch reveal, and passivation CMP for TSV reveal are coordinated as a single project.

03

Compound semiconductor specialist

InP, GaAs, GaN, LiTaO₃, and SiC each require different grinding wheels, feed rates, and subsequent CMP recipes. We process all these routinely alongside standard silicon.

04

Pre-bonding CMP for direct bonding

Our pre-bonding CMP achieves the flatness and cleanliness required for direct fusion bonding and Cu-Cu hybrid bonding, verified by AFM before the wafer advances to bonding.

05

Optical grade available

Angstrom-scale polishing for laser optics and UV substrates, requiring completely different process control from standard semiconductor CMP.

06

Surface analyzer QC included

Post-grinding and post-CMP surface quality verified by WSA (wafer surface analyzer) before proceeding. Roughness, bow, and warp data included in process data sheet.

Next in your process flow

Dicing: After CMP and thinning, the wafer is singulated into individual dies by blade dicing, stealth laser dicing, or diamond scribing.

Dicing →
RELATED SERVICE
Patterned test wafers and CMP evaluation substrates →

Custom patterned wafers built for your slurry, pad, and process-window trials.

Detailed offerings

Dedicated pages that start from this process

Wafer thinning and temporary bonding →

Thinning to 50 µm on carriers, TAIKO grinding and backside processing on carrier.

Start your project.
Initial response typically within one business day.

Share your process requirements, substrate, and production volume. A Nanosystems JP Inc. engineer will give an initial response typically within one business day. Full quote typically within 7-10 business days, subject to project complexity and NDA requirements.

To speed up technical review, please include:
substrate type & size  ·  target process  ·  quantity  ·  timeline  ·  design files if available (not required for first review)

sales@nanosystemsjp.co.jp · +81-3-5288-5569 · NDA available

Ready to discuss this process?
Initial engineering response: typically within one business day. NDA available.
Request a Quote →
Services & Industries
Capabilities Overview
Substrates
Substrate & WafersSi, SiC, GaN, glass, sapphire Fused Silica WafersQuartz · borosilicate · low CTE Glass ProcessingDrilling, etching, polishing PI Film & SUS Sensor FabRoll-to-roll · sensor patterning
Front-End
Mask FabricationGDS to chrome mask, DRC PhotolithographyE-beam 20 nm to 500 × 600 mm NanoimprintingUV & thermal NIL Thin Film DepositionPVD, CVD, ALD, MBE ALD CoatingConformal oxides, nitrides PECVD DielectricsSiO₂, SiN, SiON, a-Si TFT & BackplaneIGZO · Glass · Display Lift-OffMetal pattern · shadow mask ElectroplatingCu TSV fill, DPC, LIGA Electroforming & LIGANi shims, meshes, microstructures EtchingICP-RIE, DRIE >50:1 ICP-RIE EtchingSi, oxide, III-V, SiC, quartz MEMS FoundrySensors, actuators, microfluidics Microchannel CoolingEtched, bonded, heater test chips Thermal Test ChipsHeater dies, multi-zone, RTD Temperature SensorsPt/NiCr RTDs, thermocouples AnnealingN₂ / H₂ / vacuum / RTA Ion ImplantationB / P / As / Al / N implant CMP & GrindingCu CMP, 50 µm thinning Wafer ThinningTo 50 µm on carriers Backside MetallizationTi/Ni/Ag, Ti/Ni/Au, Ti/Cu Patterned Test WafersCustom CMP and process evaluation wafers Daisy-Chain Test DiesDummy dies, chains, bump options DicingBlade, stealth laser Stealth & Laser Dicing300 mm Si and glass, SDBG Wafer CleaningRCA, plasma, megasonic Cleaning ChemistryPiranha, SC-1, SC-2, RCA
Advanced Packaging
Wafer BondingHybrid, eutectic, fusion Anodic BondingGlass to silicon, cavities MEMS Cap WafersCavities, ports, seal lands, bonded TSV FabricationHigh AR, Cu fill InterposersSi and glass, TSV/TGV + RDL TSV RevealBackgrind → etch → CMP TGV FabricationThrough-glass via Glass TGV CouponsHole-only to routed prototypes RDL FabricationBCB / PBO / PI + damascene Packaging & AssemblyWire bond, flip-chip Flip-Chip BondingTC, reflow, AuSn, underfill 3D / 2.5D PackagingTSV + RDL + UBM + C4 AuSn BumpPVD lift-off, fluxless Laser SubmountsSi/AlN submounts, optical benches Indium BumpEvap lift-off · cryo/quantum UBM DepositionTi/Pt/Au · adhesion-barrier-Au Cu Pillar & SnAg BumpingPillars with SnAg caps, SnAg bumps Gold BumpEvap & plated · Au-Au TC AuGe / AuSi361/363 °C eutectic die attach High-Pb Bumps95Pb5Sn · hi-rel C4 SLID / TLPCu/Sn · Au/In · Ag/In Al-Ge Sealing424 °C · CMOS-friendly MEMS Ohmic ContactsGaAs · GaN · RTA + TLM SiC ProcessingThinning, films, contacts, dicing GaN & III-VGaN, GaAs, InP processing Cryo / UHV MetalAuSn · Ti/Pd/Au · rings Optical AccessWindows · meshes · holes Vapor CellsDRIE + bond · unfilled TFOI WafersQuartz-on-Si · LNOI Biochip & MicrofluidicsGlass 500 × 600 mm, NIL SiPho PackagingTSV · RDL · UBM · C4 for PIC Photonic DevicesSiN/SOI waveguides, gratings
Industries
AI & HPC PackagingCoWoS-style, 2.5D / 3D Silicon PhotonicsSOI · AuSn · TSV interposer AutomotiveMEMS sensors, SiC power Life SciencesLab-on-chip, biosensors All Industries → Request a Quote →